Electrodes, EasyCap & Accessories Mind Media offers a wide variety of electrodes and accessories. Because the NeXus product series has active amplifiers built into the encoder, you will only require our carbon coated electrode cables (with active shielding) for recording electrophysiological signals. The EasyCap shown below offers an easy way to record up to 32 channels of EEG with the NeXus-32. Sizes are from 36 to 62 cm. The standard electrode configurations is the 10-20 system and supports up to 21 (uni-polar) EEG channels. Other configurations with more electrode positions can be ordered at additional cost. Click picture for close up view Product Information TTrode3 Pregelled Triple-gel-Trode This is a special pregelled surface EMG with combined positive, negative and ground electrodes at 20 mm distances. This self-adhesive electrode is for one-time use only. Ag/AgCl based. Product Information MediTr100 Pregelled ECG/EKG/EMG electrode This is a special pregelled surface EKG/EMG electrode with a very good price-performance ratio. This self-adhesive electrode is for one-time use only. Ag/AgCl based. Normal adhesiveness. Product Information ArboEXG Pregelled ECG/EKG/EMG electrode This is a pregelled surface EKG/EMG electrode with a good price-performance ratio. This self-adhesive electrode is for one-time use only. Ag/AgCl based. Strong adhesiveness. (not suitable for children) Product Information Blue2RT3 Reusable EEG/EMG electrodes This is a reusable surface EEG/EMG electrode with a good price-performance ratio. This Ag/AgCl electrode can be used with 10-20 paste (EEG) for up to 10 times. Product Information EasyCap-XX Easy EEG cap for up to 21 channels. This is a high-quality and flexible EEG cap that uses the special sintered ring-electrodes with carbon coating and active shielding. Offers virtually (movement) artifact free EEG recording with NeXus-32. Sizes from 36-62 cm. (in steps of 2 cm) Product Information Electrogel-16fl Electrogel for the EasyCap Place the sintered ring electrodes on the EasyCap prepare the skin with NuPrep of another preparation method. Then use the 10 ml syringe with a blunt needle to fill each Ag/AgCl electrode with this conductive gel. Product Information Monoject-25 A set of 25 blunt needles This set of 25 blunt needles is used for filling the EasyCap electrodes with the electrode-gel. Needles can be reused several times. Prepare the skin with NuPrep before applying the gel. Product Information syringe10ml A 10 ml syringe This syringe is used to fill the sintered ring electrodes with electrode-gel when they are mounted on the EasyCap. Requires the blunt-needles to be ordered separately. Product Information EL1020 10-20 EEG Paste This is the standard EEG-paste for use with the NeXus-10 EEG and SCP electrodes. Prepare the skin with NuPrep and apply the 10-20 Paste on the skin and on the EEG Electrodes. Suitable for use with normal EEG and slow cortical potentials. Product Information ELNuPrep NuPrep skin preparation gel This abrasive skin preparation gel is used to prepare the skin for recording electrophysiological signals like EEG. (can be used for EMG and ECG as well). It reduces the electrode-impedance and optimizes the contact between the skin and the electrode. Product Information ELNX-VAG Pelvic Floor (Vaginal) EMG sensor This is a vaginal sensor for pelvic floor training with NeXus-10. NeXus-10 is capable or recording and feeding back both the raw EMG and the normal EMG amplitudes. This sensor is restricted for use by a single person only. Require NX-MiniDin1 Product Information ELNX-Rectal Rectal EMG training Sensor This is a rectal sensor for EMG training with the NeXus-10. NeXus-10 is capable or recording and feeding back both the raw EMG and the normal EMG amplitudes. This sensor is restricted for use by a single person only. Requires NX-MiniDin1. Product Information NX-MiniDin1 NeXus-10 mini-din adaptor cable This cable is required when using the vaginal or rectal EMG training sensor. It converts the mini-din plug on the sensor to a single-EMG channel input on the NeXus-10. A ground connector is included. Product Information NX-Adaptor1 NeXus-10 -> NeXus-16/32 Adaptor This is an adaptor cable for those people that want to use their NeXus-10 auxiliary sensors (BVP,RSP, Skin Temp. and SC) on the NeXus-16 or NeXus-32 as well. Not required when you do not use NeXus-10. Product Information EC-chinbelt EasyCap chin-belt. This is a (spare) chin-belt to be used with the EasyCap EEG electrode cap. It is required to keep the EasyCap in place during recording. Product Information ELSC-Finger SC/GSR finger electrodes This is a (spare) set of finger electrodes for the NeXus-10, 16 and 32 skin conductance sensor. This electrode can be used multiple times. Based on Ag/AgCl electrode materials.